Wescana

Wescana Industries offers Roller Gantry Systems, Conveyor Systems, Finish Rollers, Truss Stackers, Floor Truss Machines, Hydraulic Presses & Jack Presses.
  • 50 Ton Hydraulic Press with 1 1/2" Thick x 24" Wide Pressing Platen
  • Joystick Operation
  • 2' per Second Travel Speed
  • 6" Maximum Press Opening Height
  • 8' or 10' Wide x 40' or 45' Long Table
  • 1" Plastic Top over 1/2" Steel Plate
  • Unistrut Jig Rails at 12" Centers
  • 208/230/460/575 Volt - 3 Phase - 15 HP Pump Motor
  • No Finish Roller Required
  • Option: Add Floor Truss Jigging
  • Trackless Roller Gantry System
  • 24" Diameter x 1" Wall x 14' Long Gantry Roller
  • 7.5 HP / 3 Phase Gear Motor with Safety Brake
  • Controlled Motor Drive System for Start & Stop
  • Safety Barrier & Electric Eyes
  • Front & Rear Emergency Shut Off Bar
  • Joystick Operation Control
  • Ride-On Platform at Table Height
  • 2' per Second Travel Speed
  • Continuous 3/4" Steel Slotted Top Table
  • Manual Roof Jig Hardware
  • Ejectors for Side or End Eject
  • 2 Park Sections
  • Optional Wizard Ready Tables, Transfer Rollers, Exiting Conveyor, Finish Roller & Outside Conveyor
  • (2) 24" Diameter x 14' Long Rollers
  • 3 1/2" Diameter Shafts with Baffles
  • Dual 5 HP / 3 Phase Gear Motors
  • Front & Rear Emergency Shut Off Bar
  • Safety Barriers & Electric Eyes
  • Controlled Motor Drive System for Start & Stop
  • Running Amber Beacon
  • Reversing Red Beacon & Buzzer
  • Emergency Stop Control Module
  • Taper-Lock Sprockets
  • Sealed Flanged Roller Bearings
  • Revesing Magnetic Starter
  • 2' per Second Travel Speed
  • 4 Lifting Arms Stack Trusses from 20' to 60' Spans (2 HP / 3 Phase)
  • Stacking Capacity of 30 Trusses with Indexing for Each Truss Stacked
  • 28 Second Cycle Time
  • Automatic Truss Sensors to Activate Lifting Arms
  • PLC Controlled
  • 7" Touch Screen User Interface
  • Dual, Manual & Automated Electric Controls 
  • 70' Powered Outside Conveyor (1 HP / 3 Phase)
  • 7'  x 40' Table with 3/4" Steel Table Top
  • Two 5' Park Sections
  • Truss Depths from 12" to 26"
  • Truss Flip-Over Arms
  • Side or End Ejectors
  • Built-In Camber for Clamping on Both Sides
  • Air Cylinders Under Table
  • 2 Control Valves for Clamping
  • 1 Control Valve for Flip-Over Arms
  • 1 Control Vlave for Ejectors
  • 24" Diameter x 1" Wall Thickness Roller
  • 10 HP / 3 Phase Gear Motor
  • Front & Rear Emergency Shut-Off Bars
  • Joystick Control
  • 2' per Second Travel Speed 
  • 35 Ton Hydraulic Press with 14" Wide Platen
  • Press Roof or Floor Truss (4" Maximum Opening)
  • Steel Frame Table with 1/4" Steel & 1" Plastic Top
  • Slotted Jigging at 12" Centers
  • Joystick Control
  • 7.5 HP / 3 Phase (208/230/460/575 Volt)
  • 6' x 25' Table & 8' x 25' Table Available
 
Subscribe to RSS - Wescana